VW Beetle and Bus clutch: guided or unguided release bearing – and which size fits?
In short: The Type 1 engine uses two types of release bearing: unguided (up to 1970) and guided (from 1971). Which one you need is decided by the transmission – if there is a guide sleeve around the input shaft, it is guided. The clutch size (180, 200, 215 or 228 mm) on the other hand depends on the engine and flywheel. Pressure plate, release bearing and clutch disc must match each other.
At a glance
- Applies to: VW Beetle, Karmann Ghia, Thing, Type 3, VW Bus T1, T2 and T3
- Two questions before every order: guided or unguided? Which diameter?
- Rule of thumb for the type: up to 7/1970 unguided, from 8/1970 (model year 1971) guided – on the Beetle 1200 only from 1972, on the Thing from 8/1971
- Safest approach: check and measure instead of ordering by model year – transmissions and engines were often swapped
What you need
- Ruler or caliper to measure the pressure plate or clutch disc
- For fitting: a clutch alignment tool and a flywheel lock
- The matching clutch kit of pressure plate, clutch disc and release bearing (see table below)
Why you need to know the difference
At first glance, a clutch for the Type 1 engine always looks the same. But if you order the wrong type, the release bearing will not match the pressure plate: the clutch does not disengage properly, the bearing wears quickly or cannot be fitted at all. And because the engine has to come out to change the clutch, a wrong purchase is doubly annoying. Pressure plate and release bearing are not interchangeable – they must always be of the same type.
Guided or unguided – the differences
| Feature | Unguided (early type) | Guided (late type) |
|---|---|---|
| Production period (rule of thumb) | up to model year 1970 (to 7/1970) | from model year 1971 (from 8/1970) |
| Guide sleeve around the transmission input shaft | none | fitted – the release bearing slides on it |
| Release bearing | round ears, separate retaining clips | flat, square ears, wire clips moulded into the bearing |
| Pressure plate | with a ring (centering ring) on the spring fingers | no ring, the bearing presses directly on the fingers |
| Matching parts | unguided release bearing, 180 mm unguided pressure plate, 200 mm unguided pressure plate | guided release bearing, guide sleeve, 200 mm guided pressure plate |
With the guided system, the guide sleeve keeps the release bearing straight. Without the sleeve the bearing can tilt and no longer sits fully against the pressure plate. If the sleeve is missing on a late transmission, it must be replaced – it is available as a release bearing guide sleeve and as an OE version with oil drain hole.
Step by step: how to find out what you need
- Look at the transmission. With the engine removed, look at the bell housing: if there is a metal sleeve around the input shaft, your transmission is guided. If not, it is unguided. The transmission is what counts – not the model year of the vehicle.
- Check the old release bearing. Round ears with separate clips = unguided. Flat ears with moulded wire clips = guided.
- Look at the pressure plate. If a ring is fitted in the centre on the spring fingers, it belongs to the unguided system.
- Measure the diameter. Measure the clutch disc or pressure plate across its diameter. The result is 180, 200, 215 or 228 mm. If the flywheel or engine has been swapped, the size no longer matches the model year – measuring is then the only reliable method.
- Order the matching kit – type and size from steps 1 to 4.
Clutch sizes at a glance
| Size | Engines | Vehicles (examples) | Clutch kit |
|---|---|---|---|
| 180 mm (7.1 in) | Type 1 engine 25 and 30 PS, 1200 cc up to 1980 (up to engine no. D 1 455 271), 1300 cc | Beetle 1200 and 1300, Bus T1 with small engine, Karmann Ghia 1200/1300 | 180 mm unguided · LuK 180 mm unguided · Sachs 180 mm guided |
| 200 mm (7.9 in) | Type 1 engine 1200 cc from 1980 (from engine no. D 1 455 272), 1500 cc, 1600 cc; also AJ, AL and ACD | Beetle 1500, 1600, 1302/1303, Karmann Ghia 1500/1600, Thing, Bus T1/T2 with 1500/1600 up to model year 1975 | 200 mm unguided · LuK 200 mm unguided · 200 mm guided · LuK 200 mm guided |
| 215 mm (8.5 in) | Type 1 engine 1600 cc in the Bus from model year 1976 (AS/AF, from chassis no. 216 2118 506), CT/CZ, Type 4 engine 1800 cc (AP/AW) depending on year, early Wasserboxer 1.9 l (DF/DG/DH up to 1983) | Bus T2 from 1976, Bus T3 1.6 l air-cooled and early Wasserboxer | 215 mm clutch kit · Sachs 215 mm |
| 228 mm (9.0 in) | Type 4 engine 1800 cc (ED) and 2000 cc, Wasserboxer from 1983 and 2.1 l | Bus T2 2.0 l, Bus T3 2.0 l and Wasserboxer | Sachs 228 mm Type 4 · Sachs 228 mm Bus T3 |
The limits for the Bus T2 and the Type 4 engine depend on the chassis number. With mixed engines, conversions or vehicles from Brazil and Mexico, only measuring helps. If in doubt, call us or send us a photo.
Flywheel and ring gear: 6 volt or 12 volt
The flywheel always matches the clutch diameter. When replacing the flywheel or ring gear, also check the electrical system: vehicles with a 6-volt system have a ring gear with 109 teeth, vehicles with a 12-volt system a ring gear with 130 teeth. The starter must match.
Tips from the workshop
- Always replace the complete kit: If the clutch disc is worn, the pressure plate and release bearing will soon follow. As the engine is out anyway, the complete kit is worth it.
- Don't forget to centre: Align the clutch disc with the alignment tool before tightening the pressure plate – otherwise the engine will not mate with the transmission. Tighten the pressure plate in a cross pattern to 25 Nm (18 ft-lb), using new pressure plate mounting bolts.
- Lightly grease the guide sleeve: A thin film of clutch grease on the sleeve lets the guided release bearing slide smoothly.
- Old transmission, new clutch? An unguided transmission can be converted to the guided type with conversion parts – but this is not a standard job. Ask us first.
Common mistakes
- Type ordered by model year: If the transmission has been swapped, the clutch will not fit. Always check for the guide sleeve.
- Guided bearing fitted without a sleeve: The bearing tilts and wears quickly.
- Ring on the pressure plate with the guided system: Pressure plate and bearing do not belong together.
- Size not measured: After an engine swap there is often a different flywheel fitted.
Frequently asked questions
How can I tell whether my Beetle has a guided clutch?
From the transmission: if there is a guide sleeve around the input shaft, it is guided. In addition, the guided pressure plate has no ring on the spring fingers, and the release bearing has flat ears with moulded clips.
Which clutch does the Beetle 1300 and the Beetle 1600 have?
The 1300 has a 180 mm clutch, the 1600 (including 1302 and 1303) a 200 mm clutch. Whether it is guided or unguided depends on the transmission – from model year 1971 it is usually guided.
Can I fit a 200 mm clutch instead of 180 mm?
Only together with a matching 200 mm flywheel. Clutch and flywheel must always have the same diameter.
Matching parts and more guides
- VW Beetle clutch & flywheel, VW Bus T1 clutch, VW Bus T2 clutch and VW Bus T3 clutch
- Individual parts: 180 mm clutch disc, 200 mm clutch disc, unguided release bearing, guided release bearing
- More guides: Identifying your gearbox, Adjusting the clutch and replacing the clutch cable, Identifying your engine and Type 1 engine torque specs – all guides are in our Guides & Tips overview.
All information without guarantee. If in doubt, send us a photo of your transmission, pressure plate or release bearing – we will help you identify it. All work is carried out at your own risk.