VW Bus T2 technical data and specs: ignition timing, valve clearance, compression, oil and tyre pressures for 1.6 to 2.0 litres

In short: Here you find all important settings for the VW Bus T2 (1967–1979) according to VW factory data – for the 1.6 l Type 1 engine and the big Type 4 engines with 1.7, 1.8 and 2.0 litres: ignition timing by engine code, idle speed and CO, dwell angle, spark plugs, valve clearance, compression, oil capacities, torque specs, tyre pressures and electrics. We also show you how to set the ignition timing on the Type 4 engine.

At a glance

  • Fits: VW Bus T2a and T2b, model years 1968 to 1979
  • Engines: 1.6 l (Type 1: AD, AS, B, AF, C), 1.7 l (CA, CE), 1.8 l (AP, ED), 2.0 l (CJ, GD, GE)
  • Also for US-spec buses: fuel-injected ED, GD and GE engines in USA, Canada and California versions
  • Important: the values depend on the engine code – identify your engine first, not the model year of the bus

What you need

  • Timing light and tach/dwell meter
  • Feeler gauge 0.15 and 0.20 mm (0.006 and 0.008 in) for the valve clearance
  • On the Type 4 engine a readable ignition timing scale (021 119 249 E)
  • Torque wrench and compression tester

Identify the engine first

The T2 was built with two very different engines: the 1.6 l Type 1 engine (as in the Beetle, with oil strainer) and the Type 4 engine with 1.7 to 2.0 litres (flat "pancake" fan housing, oil filter). Because engines were often swapped, the code on the engine always counts. Where to find it is explained in our guide Identifying your engine.

Ignition timing VW Bus T2 by engine

Engine oil temperature at least 30 °C (86 °F). The "vacuum hose" column tells you whether the hoses must be disconnected or stay connected while setting the timing.

Engine Code / engine number Ignition timing Idle rpm Vacuum hose
1.6 l B 0 000 001 – B 0 455 475
B 5 000 001 – B 5 187 969
0° (TDC) 850 ± 50 disconnected
1.6 l (dual-vacuum distributor) AD 0 000 002 – AD 290 640 5° ATDC 850 ± 50 connected
1.6 l AD 290 641 – AD 999 999
AS 000 001 –
7.5° BTDC 875 ± 75 disconnected
1.6 l dished pistons C 0 000 001 – C 0 056 580 0° (TDC) 850 ± 50 disconnected
1.6 l dished pistons (dual-vacuum distributor) AF 000 002 – AF 014 841 5° ATDC 850 ± 50 (throttle closed) connected
1.6 l dished pistons AF 014 842 – 7.5° BTDC 875 ± 75 disconnected
1.7 l CA 000 001 – CA 020 000 5° ATDC 900 ± 50 connected
1.7 l CA 020 001 – 7.5° BTDC 900 ± 50 disconnected
1.7 l CE 000 001 – 7.5° BTDC 950 ± 50 disconnected
1.8 l / 2.0 l manual AP 000 001 – / CJ 000 001 – 7.5° BTDC 875 ± 75 disconnected
1.8 l / 2.0 l automatic AP 000 001 – / CJ 000 001 – 7.5° BTDC 950 ± 50 disconnected
2.0 l Sweden from MY 1976 GD and GE (manual / automatic) 7.5° BTDC 875 ± 75 / 925 ± 75 disconnected
1.8 l fuel injection USA/Canada/California, MY 1975 ED 000 001 – 5° ATDC 900 ± 50 / 950 ± 50 connected
2.0 l fuel injection USA/Canada/California, MY 1976–77 GD 000 001 – 7.5° BTDC 900 ± 50 / 950 ± 50 disconnected
2.0 l fuel injection USA/Canada MY 1978–79, California MY 1978 (hydraulic lifters) GE 000 001 – 7.5° BTDC 875 ± 75 / 925 ± 75 disconnected
2.0 l fuel injection California, MY 1979 (Hall sender, breakerless ignition) GE 5° ATDC 875 ± 75 / 925 ± 75 connected

US-spec buses: the fuel-injected ED, GD and GE engines in USA, Canada and California versions have their own values – the 1.8 l ED and the California GE from model year 1979 are set to 5° ATDC with the hoses connected. Where two idle values are given, the first is for manual, the second for automatic.

Idle speed and CO content

Engine Idle rpm CO vol. %
1.6 l up to MY 1975 850 ± 50 3 ± 1
1.6 l from MY 1976 875 ± 75 2 ± 1
1.7 l / 1.8 l / 2.0 l manual 875 ± 75 3 ± 1
1.7 l / 1.8 l / 2.0 l automatic 950 ± 50 3 ± 1
2.0 l Sweden from MY 1976 (GD and GE) manual / automatic 875 ± 75 / 925 ± 75 1.0 ± 0.5

US fuel-injected ED, GD and GE engines: idle speed see the ignition timing table. CO content on the GE from model year 1979: 1.0 ± 0.5 % (USA/Canada) or 0.7 ± 0.5 % (California).

Dwell angle and spark plugs

Dwell angle: setting 47 ± 3° (53 ± 3 %), wear limit 42–58°.

Engine Spark plug Electrode gap Torque
1.6 l (Type 1 engine) Bosch W8AC 0.6–0.8 mm (0.024–0.031 in) 20 Nm (15 ft-lb)
1.7 l / 1.8 l / 2.0 l (Type 4 engine) Bosch W8CC 0.6–0.8 mm (0.024–0.031 in) 20 Nm (15 ft-lb)

Valve clearance, compression and oil pressure

Valve clearance with the engine cold: intake 0.15 mm (0.006 in), exhaust 0.15 mm (0.006 in). With sodium-filled exhaust valves 0.20 mm (0.008 in) – you can tell by the sticker on the engine.

Exception GE (2.0 l from model year 1978): these engines have hydraulic lifters – no valve clearance is set, leave the adjusting screws as they are. You can recognise them by the engine code GE and by the sticker in the engine bay on which the valve clearance field is crossed out in red.

Compression (throttle fully open, engine oil at least 30 °C / 86 °F). Maximum difference between cylinders: 2 bar (29 psi) on the 1.6 l, 3 bar (44 psi) on the 1.7–2.0 l.

Engine Codes new wear limit
1.6 l AD, AS, B 8.0–10.0 bar (116–145 psi) 7.0 bar (102 psi)
1.6 l dished pistons AF, C 6.0–8.0 bar (87–116 psi) 5.0 bar (73 psi)
1.7 l CA, CE 7.0–9.5 bar (102–138 psi) 6.0 bar (87 psi)
1.8 l AP 6.0–9.5 bar (87–138 psi) 5.0 bar (73 psi)
2.0 l CJ, GD, GE 6.0–9.5 bar (87–138 psi) 5.0 bar (73 psi)

Oil pressure: at least 2.0 bar (29 psi) at approx. 80 °C (176 °F) oil temperature and approx. 2000 rpm. The oil pressure switch opens at 0.15–0.45 bar (2–7 psi).

Engine oil and engine torque specs

Oil capacities

Engine with filter change without filter change
1.6 l (Type 1 engine, oil strainer) – 2.5 l (2.6 US qt)
1.7 l / 1.8 l / 2.0 l (Type 4 engine) 3.5 l (3.7 US qt) 3.0 l (3.2 US qt)

How to change the oil on the Type 1 engine is shown in our guide Oil change.

Engine torque specs

Fastener 1.6 l 1.7 l / 1.8 l / 2.0 l
Spark plug to cylinder head 20 Nm (15 ft-lb) 20 Nm (15 ft-lb)
Oil drain plug to crankcase 35 Nm (26 ft-lb) 25 Nm (18 ft-lb)
Oil strainer cover to crankcase 8 Nm (6 ft-lb) 13 Nm (10 ft-lb)
Oil pressure switch (with sealant) 10 Nm (7 ft-lb) 10 Nm (7 ft-lb)
Oil filter flange to crankcase – 20 Nm (15 ft-lb)
Crankshaft pulley 45 Nm (33 ft-lb) –
Fan to hub – 20 Nm (15 ft-lb)
Fan hub to crankshaft – 30 Nm (22 ft-lb)
Engine to transmission 30 Nm (22 ft-lb) 30 Nm (22 ft-lb)
Engine carrier to body 25 Nm (18 ft-lb) 25 Nm (18 ft-lb)

Clutch, transmission and fan belt

  • Clutch free play: 10–25 mm (3/8–1 in) at the pedal
  • Manual transmission oil: GL 4 SAE 80, filled to the edge of the filler hole
  • Automatic: ATF Dexron, refill approx. 3.0 l (3.2 US qt), difference min./max. 0.4 l; final drive GL 5 SAE 90
  • Fan belt tension (thumb pressure): new belt approx. 2 mm (0.08 in), used belt approx. 5 mm (0.2 in) deflection
Fastener Torque
Drive shaft to flange 45 Nm (33 ft-lb)
Transmission carrier to rear rubber mount 35 Nm (26 ft-lb)
Transmission to transmission carrier 35 Nm (26 ft-lb)
Front rubber mount to transmission 25 Nm (18 ft-lb)
Stop to frame 45 Nm (33 ft-lb)

Running gear: checks

Check Specification
Steering play at the rim roller steering max. 15 mm (0.59 in), worm-and-peg steering max. 25 mm (1.0 in)
Tie rod ends no play
Total toe, front +15′ ± 15′ (equals 0–3.6 mm / 0–0.14 in)
Camber, front +0° 40′ ± 20′, difference left/right max. 30′
Brake lining wear limit drum brake 2.5 mm (0.10 in), disc brake 2.0 mm (0.08 in)
Brake pedal free play max. 1/3 of pedal travel
Brake fluid DOT 3 or DOT 4

All torque specs for front axle, steering, rear axle and brakes are in our guide Chassis torque specs Beetle & Bus T2.

Tyre pressures VW Bus T2

Values front / rear for radial tyres. Add 0.2 bar (3 psi) for winter tyres. If there is a tyre pressure sticker in the vehicle, its values apply.

Model 8/1967–7/1971 radial from 8/1971 185 SR 14 reinforced from 8/1971 185 R 14 C Spare
VW Bus (model 22) 2.1 / 2.6 bar (30 / 38 psi) 2.1 / 2.9 bar (30 / 42 psi) 2.1 / 3.1 bar (30 / 45 psi) 4.0 bar (58 psi)
VW Bus L (model 24) 2.1 / 2.6 bar (30 / 38 psi) 2.1 / 2.9 bar (30 / 42 psi) 2.1 / 3.1 bar (30 / 45 psi) 4.0 bar (58 psi)
Panel van, Kombi, pick-up (model 21, 23, 26) 2.1 / 2.7 bar (30 / 39 psi) 2.1 / 2.9 bar (30 / 42 psi) 2.1 / 3.1 bar (30 / 45 psi) 4.0 bar (58 psi)

Electrics: checks

Check Specification
Regulator voltage 12.5–14.5 V
Alternator 50 A / 55 A / 70 A 30 A / 35 A / 50 A load current at 3000 rpm engine speed
Alternator brushes new 10 mm (0.39 in), wear limit 5 mm (0.20 in)
Battery acid density discharged 1.12 · half charged 1.20 · charged 1.28 kg/dm³
Battery acid level 5 mm (0.2 in) above the separators or to the mark

Step by step: setting the ignition timing on the Type 4 engine

On the 1.6 l Type 1 engine the marks are on the crankshaft pulley at the front – see our guide Ignition timing. On the Type 4 engine (1.7–2.0 l) you read the timing through the opening in the fan housing on a degree scale:

  1. Preparation: set the valve clearance and the dwell angle (47 ± 3°) first – only then is the timing correct.
  2. Find the marks: on the Bus the timing mark is on the rear rim of the pulley, on some engines on the fan. Clean the mark and the scale and highlight them with white paint.
  3. Warm up the engine: engine oil at least 30 °C (86 °F).
  4. Connect: timing light to cylinder 1, connect the tachometer.
  5. Vacuum hose: disconnect (and plug) or leave connected depending on the engine – see table above.
  6. Check with the light: at idle according to the table (e.g. CJ manual 875 ± 75 rpm) the mark must be at 7.5° BTDC on the scale (CA up to no. 020 000: 5° ATDC).
  7. Adjust: loosen the distributor clamp bolt, turn the distributor until the mark is right, tighten the clamp bolt.
  8. Check: check and adjust the idle speed, reconnect the vacuum hoses.

Tips from the workshop

  • No mark visible? If a pulley from another Type 4 engine has been fitted, the mark can be missing. Find TDC on cylinder 1 and mark it again.
  • Dual-vacuum distributor: early AD and AF engines and the early CA are set to 5° ATDC with the hoses connected – not to 7.5° BTDC.
  • Long-reach spark plugs: the Type 4 engine needs plugs with 19 mm thread reach, e.g. the Bosch W8CC.
  • Always test compression on all four cylinders: the difference between cylinders matters as much as the value itself.
  • Removing hydraulic lifters on the GE: keep the lifters in cylinder order and stand them upright, base down, so no oil runs out. Before fitting, test with your thumb: if the plunger gives way under firm pressure, the lifter must be bled. A hydraulic lifter cannot be repaired – replace it if in doubt.
  • Distributor on fuel-injected engines (ED, GD, GE): the distributor base holds a second set of contacts that sends engine speed to the control unit. So do not simply swap it for a carburettor distributor. On USA/Canada buses up to model year 1978 the distributor also limits engine speed to approx. 5,240–5,560 rpm.
  • California GE from 1979 with Hall sender: never connect a condenser to terminal 1 (−) of the coil, replace the coil only with the same type and connect or disconnect wires only with the ignition off – otherwise the control unit will be damaged.

Common mistakes

  • Values by model year instead of engine code: many T2s now have a different engine than from the factory.
  • Wrong vacuum hose setting: with the hose connected instead of disconnected (or vice versa) the timing will be wrong.
  • Type 1 values on the Type 4 engine: oil capacity, drain plug torque and spark plugs differ.
  • Timing set before the dwell angle: every change to the dwell angle shifts the ignition timing.

Frequently asked questions

What is the ignition timing of the VW Bus T2 with the 2.0 l engine?

7.5° BTDC with the vacuum hose disconnected, idle 875 ± 75 rpm (manual) or 950 ± 50 rpm (automatic). Exception: the California version with engine code GE from model year 1979 (breakerless ignition) is set to 5° ATDC with the hoses connected.

What is the ignition timing of the fuel-injected US-spec T2?

According to the VW repair manual for US tourist vehicles: 1.8 l ED (1975) 5° ATDC with the hoses connected, 2.0 l GD (1976–77) and GE (USA/Canada 1978–79) 7.5° BTDC with the hoses disconnected, 2.0 l GE California 1979 5° ATDC with the hoses connected.

How much oil does the Type 4 engine in the T2 take?

3.5 litres (3.7 US qt) with filter change, 3.0 litres (3.2 US qt) without. The 1.6 l Type 1 engine takes 2.5 litres (2.6 US qt).

What is the valve clearance on the VW Bus T2?

0.15 mm (0.006 in) for intake and exhaust with the engine cold, 0.20 mm (0.008 in) with sodium-filled exhaust valves. Exception: the 2.0 l engine with code GE (from model year 1978) has hydraulic lifters – no valve clearance is set there.

What tyre pressure applies to the T2?

For the VW Bus from 8/1971 with 185 R 14 C front 2.1 and rear 3.1 bar (30 / 45 psi), with 185 SR 14 reinforced 2.1 / 2.9 bar (30 / 42 psi).

Matching parts and more guides

Values according to VW factory data (V.A.G technical data, Transporter from 1979, and VW pocket book Type 1 and 2). All information without guarantee. If in doubt, send us the engine code – we will help you identify it. All work is carried out at your own risk.