Tensioning and replacing the fan belt on the VW Beetle and Bus T1/T2 (Type 1 engine) – step by step
In short: On the Type 1 engine of the VW Beetle, Karmann Ghia and Bus T1/T2, the fan belt drives the generator and the cooling fan. Pressed firmly with your thumb in the middle, it should deflect 10–15 mm (3/8–5/8 in). You set the tension with the shims on the generator pulley and tighten the nut to 60 Nm (44 ft-lb).
At a glance
- Difficulty: easy
- Time: approx. 20–30 minutes
- Fits: VW Beetle, Karmann Ghia, VW Bus T1 and T2 with Type 1 engine
- When: check the tension at every service; replace the belt if it is cracked, frayed at the edges or glazed and hardened on the sides
What you need
- The right fan belt: 10 × 905 mm for DC generator, 11.3 × 912 mm for alternator or 10 × 900 mm for 170 mm crankshaft pulley
- Shims for the generator pulley (10 pieces), if any are missing
- 21 mm ring or socket wrench, a sturdy screwdriver to hold the pulley, torque wrench
Why the fan belt is so important on an air-cooled engine
On the Type 1 engine the cooling fan sits directly on the generator shaft. So the fan belt drives not only the charging system but the entire engine cooling. If it is too loose, it slips – the engine runs too hot and the battery is not charged properly. If it is too tight, the bearings of the generator and fan are overloaded. And if it snaps, the cooling stops immediately.
Important: If the red charging warning light suddenly comes on while driving, the fan belt may have snapped. Stop immediately and switch off the engine – without the belt the cooling fan does not turn and the engine overheats within a short time.
The right values
| Belt tension | 10–15 mm (3/8–5/8 in) deflection midway between the pulleys under firm thumb pressure |
| Generator pulley nut | 21 mm, 60 Nm (44 ft-lb) |
| Adjustment principle | Shim out from between the pulley halves = more tension, shim in = less tension |
Step by step: tensioning the fan belt
- Check the tension. Engine off. Press firmly on the belt with your thumb midway between the crankshaft pulley and the generator pulley. If it deflects 10–15 mm (3/8–5/8 in), everything is fine.
- Loosen the nut. Put a sturdy screwdriver into the notch of the inner pulley half and brace it against the upper generator housing bolt. This holds the pulley while you undo the 21 mm nut.
- Remove the outer pulley half. The shims sit underneath, between the two pulley halves.
- Move the shims. If the belt is too loose, take one shim out from between the halves. If it is too tight, add one. Put every shim you take out on the outside between the pulley half and the nut – that way none get lost and the total number stays the same.
- Reassemble. Fit the outer half, screw on the nut and tighten it to 60 Nm (44 ft-lb). Keep turning the pulley a little as you tighten, so the belt seats cleanly in the groove and does not get pinched between the pulley halves.
- Check again. Test the tension with your thumb again. If it is not right yet, repeat the steps with one shim more or less.
Step by step: replacing the fan belt
- Open the pulley as described above: hold it, loosen the nut, remove the outer half and the shims.
- Remove the old belt and compare it with the new one – length and width must match (DC generators and alternators need different belts).
- Fit the new belt – first onto the crankshaft pulley, then onto the inner half of the generator pulley.
- Tension and tighten as above: distribute the shims, fit the outer half, tighten the nut to 60 Nm (44 ft-lb) while turning the pulley.
- Check again after a few hundred kilometres (a few hundred miles). A new belt stretches slightly at first and may need tightening by one shim.
Tips from the workshop
- Carry a spare belt: A fan belt costs little, an overheated engine a lot. Pack a matching belt and a 21 mm wrench for every longer trip.
- Worn pulley? If the groove of the generator pulley is worn or bent, it will eat every new belt. Then a new generator pulley is worth it.
- Belt squeals? Usually it is too loose or hardened. Tension it first – if it keeps squealing, replace it.
- Looks and protection: A fan belt guard protects fingers and wires from the running belt.
Common mistakes
- Shims left out instead of stored on the outside: They are then missing at the next belt change.
- Belt pinched while tightening: If you do not turn the pulley while tightening, the belt gets squeezed between the halves – it ends up too tight and wears quickly.
- Belt too tight: Overloads the generator and fan bearings.
- Wrong belt: DC generators and alternators need different belt sizes.
Frequently asked questions
How tight should the fan belt be on a Beetle?
Pressed firmly with your thumb midway between the pulleys, it should deflect 10–15 mm (3/8–5/8 in).
Which fan belt do I need for my Beetle?
That depends on the generator and the crankshaft pulley: DC generators usually use 10 × 905 mm, alternators 11.3 × 912 mm, and with a 170 mm crankshaft pulley 10 × 900 mm. The safest way is to compare with the old belt.
What happens if the fan belt snaps?
The charging warning light comes on and – more importantly – the cooling fan stops. Stop immediately and switch off the engine, otherwise it will overheat.
Matching parts and more guides
- VW Karmann Ghia lighting & electrics with fan belts and pulleys, VW Beetle engine parts
- VW Bus T1 engine parts and VW Bus T2 engine
- More guides: Adjusting the clutch and replacing the clutch cable, Oil change and Ignition timing – all guides are in our Guides & Tips overview.
All work is carried out at your own risk. If you are unsure, a specialist workshop will help you.