Installing the distributor and connecting the plug leads: firing order 1-4-3-2 and finding TDC on the VW Beetle and Bus

In short: The Type 1 engine in the VW Beetle and Bus fires in the order 1 – 4 – 3 – 2. The rotor turns counter-clockwise: cylinder 1 sits on the distributor cap above the notch on the distributor body, followed counter-clockwise by 4, 3 and 2. Here we show you how to set cylinder 1 to TDC, install the distributor correctly and connect the plug leads – so your engine starts straight away after the repair.

At a glance

  • Difficulty: easy to medium
  • Time: approx. 30 minutes
  • Fits: VW Beetle, Karmann Ghia, Thing, VW Bus T1 and T2 with Type 1 engine (1200–1600 cc)
  • Important: always mark the plug leads before pulling them off

What you need

  • Wrench for the crankshaft pulley (to turn the engine) and spark plug socket
  • Tape and a pen to mark the plug leads
  • Feeler gauge (point gap 0.4 mm / 0.016 in) and test lamp or timing light
  • If needed: new distributor cap, rotor and plug lead set

Why the firing order matters

Each cylinder needs its spark exactly when its piston is at the top of the compression stroke. If two plug leads are swapped or the distributor sits one tooth out, the engine starts badly or not at all, runs on only two or three cylinders, or backfires through the carburettor or exhaust. With the correct firing order and cylinder 1 at TDC as your starting point, you get everything back in the right order.

The key facts at a glance

What Type 1 engine (Beetle, Karmann Ghia, Bus T1/T2 1.6 l)
Firing order 1 – 4 – 3 – 2 (cast into the generator stand)
Cylinder numbers seen from the rear 1 and 2 on the right, 3 and 4 on the left; 1 and 3 at the front (towards the middle of the car), 2 and 4 at the rear by the pulley
Crankshaft rotation clockwise (looking at the pulley)
Rotor rotation counter-clockwise (seen from above)
Plug leads on the cap cylinder 1 above the notch on the distributor body, then counter-clockwise 4, 3, 2
Distributor drive with cylinder 1 at TDC slot at right angles to the engine centre line, smaller half facing the crankshaft pulley

Firing order 1-4-3-2: plug leads on the distributor cap of the VW Beetle and Bus Type 1 engine

Step by step: setting cylinder 1 to TDC

  1. Remove the distributor cap – push the spring clips aside. The plug leads stay in the cap.
  2. Turn the crankshaft: turn the pulley clockwise until the mark on the pulley lines up with the crankcase split.
  3. Check the rotor: it must point to the notch on the rim of the distributor body. If it points exactly the other way, cylinder 3 is at TDC – turn the crankshaft one full turn further.
  4. Check the rocker arms: at firing TDC both rocker arms of cylinder 1 have some play, the valves are closed.
  5. Without a readable mark: remove the spark plug of cylinder 1, put your thumb over the plug hole and turn the crankshaft slowly. When air pushes against your thumb, cylinder 1 is on its compression stroke – shortly after that the piston is at the top.

Step by step: installing the distributor

  1. Set cylinder 1 to TDC (see above) – on the compression stroke, not on the overlap TDC.
  2. Check the distributor drive: the slot at the top of the distributor drive shaft is offset. It must be at right angles to the engine centre line, with the smaller half facing the crankshaft pulley.
  3. Fit the distributor: point the rotor at the notch on the distributor body and insert the distributor. Turn it gently back and forth until the drive dog engages in the slot of the drive shaft.
  4. Tighten the clamp – at first only so tight that you can still turn the distributor for adjustment.
  5. Set point gap and ignition timing: 0.4 mm (0.016 in) point gap, then the ignition timing – as described in our guide Ignition timing.

Caution: if you have to pull out the distributor drive shaft, the thrust washer underneath must never drop into the engine – otherwise the engine has to be taken apart. The shaft can be pulled out safely with a distributor drive puller.

Step by step: connecting the plug leads correctly

  1. Fit the cap correctly: the terminal the rotor points to with cylinder 1 at TDC (above the notch) belongs to cylinder 1.
  2. Continue counter-clockwise: the next terminal counter-clockwise is cylinder 4, then cylinder 3, then cylinder 2.
  3. Route the leads to the cylinders: 1 and 2 to the right side of the engine, 3 and 4 to the left (seen from the rear); 1 and 3 at the front, 2 and 4 at the rear by the pulley.
  4. Centre lead from the ignition coil into the middle of the distributor cap, push all connectors firmly home.

Tips from the workshop

  • Mark before pulling off: a strip of tape with the cylinder number on every plug lead saves you the search later.
  • Replace leads one at a time: with a new plug lead set pull off only one lead at a time and replace it with the new one – that way nothing gets mixed up.
  • Read the firing order on the engine: on the Type 1 engine it is cast into the generator stand.
  • Check while you are at it: with the distributor out, take a look at cap, rotor and points – all together in the Type 1 engine service kit.

Common mistakes

  • Plug leads connected clockwise: the rotor turns counter-clockwise – connected clockwise the order is wrong.
  • Overlap TDC instead of firing TDC: if the mark is at the split but the rotor points the other way, the distributor is 180° out. Turn the crankshaft one more turn or move the leads accordingly.
  • Drive shaft one tooth out: the distributor can then no longer be turned into the adjustment range. Reset the drive shaft.
  • Ignition timing not reset: after every distributor removal, check point gap and ignition timing.

Frequently asked questions

What is the VW Beetle firing order?

1 – 4 – 3 – 2. This applies to all Type 1 engines in the Beetle, Karmann Ghia and Bus, and also to the Type 4 engine in the Bus T2.

Which way does the Beetle rotor turn?

Counter-clockwise, seen from above. That is why the plug leads are connected counter-clockwise from cylinder 1 in the order 4, 3, 2.

Where is cylinder 1 on a Beetle?

Seen from the rear of the engine at the front right – on the right side, towards the middle of the car. Cylinder 2 sits behind it by the pulley.

How do I find TDC without a mark?

Remove the spark plug of cylinder 1, put your thumb over the plug hole and turn the crankshaft. When air pushes against your thumb, cylinder 1 is on its compression stroke and just before TDC.

Matching parts and more guides

All information without guarantee. All work is carried out at your own risk. If in doubt, a specialist workshop will help you.