Front Axle & Steering VW Bus T3
123453678910111213141516171819202122182324252627282924222330311234536789101516232425202132262728292422233031
Exploded view of the front axle VW Bus T3 (05/1979–07/1992) – click a number to go straight to the matching part. More parts that are not included in the drawing can be found in the product list below.
- Self-locking nut upper control arm bolt
- Washer upper control arm bolt
- Upper control arm bush
- Eccentric washer upper control arm 4 mm
- Eccentric washer upper control arm 5.5 mm
- Upper control arm bolt
- Upper ball joint · Meyle HD
- Shock absorber dust cap
- Stabiliser bush inner 19 mm
- Stabiliser clamp from 08/1984
- Stabiliser bush inner 21 mm
- Stabiliser clamp up to 07/1984
- Stabiliser link bush 23 mm
- Stabiliser link bush 19 mm
- Stabiliser link bush 21 mm
- Stabiliser link straight from 08/1984 · alternative
- Stabiliser link curved up to 07/1984
- Washer stabiliser link up to 07/1984
- Damping ring stabiliser link up to 07/1984
- Lower control arm bush
- Lower control arm bolt
- Spacer stabiliser link
- Plate stabiliser link from 08/1984
- Damping ring stabiliser link from 08/1984
- Spring washer lower control arm bolt
- Self-locking nut tension strut
- Spacer tension strut bush
- Tension strut bush front
- Tension strut bush rear
- Lower ball joint · Meyle HD
- Hub nut (wheel bearing adjustment)
- Tension strut
Front Axle & Steering for Your VW Bus T3
The front axle of your VW Bus T3 (1979–1992) carries a lot of weight. Bushes, ball joints and tension strut rubbers therefore wear over the years – the bus clunks, wanders on the straight or the steering feels vague. Here you will find the parts to get the front axle and steering back in shape.
Above you can see the exploded view of the front axle: click a number to go straight to the matching part.
What you will find here
- Control arms & bushes: control arms, upper and lower bushes, bolts, eccentric washers, washers and nuts
- Ball joints: upper and lower, also in Meyle HD quality
- Tension struts & stabiliser: tension struts, strut bushes, stabiliser bushes, clamps, links and fitting kits
- Suspension: shock absorbers, coil springs, bump stops and protective tubes
- Wheel bearings & hubs: wheel bearing kits, seals, hub nuts and hub caps
- Steering: steering boxes, tie rods and tie rod ends, axial joints, flex discs, intermediate shaft, power steering parts and steering wheels
Up to 07/1984 or from 08/1984?
Check the year for the stabiliser: up to 07/1984 the T3 has a curved stabiliser link, from 08/1984 a straight one with different rubbers and plates. The clamps for the stabiliser bushes differ as well. Choose the bushes to match your stabiliser diameter (19, 21 or 23 mm).
Tip
Ideally replace bushes and joints on both sides at the same time and have the alignment checked afterwards. Always renew self-locking nuts. You will find matching parts in Brakes & Wheels VW Bus T3 and Rear Axle & Drive Shafts VW Bus T3.
Frequently Asked Questions about the VW Bus T3 Front Axle
How do I recognise worn bushes or ball joints?
Typical signs are clunking over bumps, wandering on the straight, uneven tyre wear and a bus that pulls to one side under braking. With the vehicle raised, check whether the control arms, tension strut or joints have play and whether the rubbers are cracked.
Do I need an alignment after replacing parts?
Yes. After replacing control arm bushes, ball joints, tension struts or tie rods you should have camber, caster and toe adjusted. On the T3, camber and caster are set using the eccentric washers on the upper control arm.